One-dimensional shape memory alloy models for use with reinforced composite structures

A. J. Zak*, M. P. Cartmell, W. M. Ostachowicz, M. Wiercigroch

*Corresponding author for this work

Research output: Contribution to journalArticle

57 Citations (Scopus)

Abstract

In this paper three models of the shape memory alloy behaviour have been presented and re-investigated. The models are attributed to Tanaka, Liang and Rogers, and Brinson, and have been used extensively in the literature for studying the static or dynamic performance of different composite material structures with embedded shape memory alloy components. The major differences and similarities between these models have been emphasised and examined in the paper. A simple experimental rig was designed and manufactured to gain additional insight into the main mechanics governing the shape memory alloy (SMA) mechanical properties. Data obtained from the experimental measurements on Ni-Ti wires have been used in the numerical simulation for validation purposes. It has been found that the three models all agree well in their predictions of the superelastic behaviour at higher temperatures, above the austenite finish temperature when shape memory alloys stay in the fully austenitic phase. However, at low temperatures, when the alloys stay in the fully martensitic phase, some difficulties may be encountered. The model developed by Brinson introduces two new state variables and therefore two different mechanisms for the instigation of stress-induced and temperature-induced martensite. This enables more accurate predictions of the superelastic behaviour. In general, it can be recommended that for investigations of the shape memory and superelastic behaviour of shape memory alloy components the Brinson model, or refinements based on the Brinson model, should be applied.

Original languageEnglish
Pages (from-to)338-346
Number of pages9
JournalSmart Materials & Structures
Volume12
Issue number3
DOIs
Publication statusPublished - 28 Apr 2003

Keywords

  • natural frequencies
  • thermomechanical behavior
  • constitutive model
  • damping behavior
  • flexible beam
  • elastic beam
  • SMA wires
  • plate
  • transformation
  • deformation

ASJC Scopus subject areas

  • Signal Processing
  • Atomic and Molecular Physics, and Optics
  • Civil and Structural Engineering
  • Materials Science(all)
  • Condensed Matter Physics
  • Mechanics of Materials
  • Electrical and Electronic Engineering

Cite this

One-dimensional shape memory alloy models for use with reinforced composite structures. / Zak, A. J.; Cartmell, M. P.; Ostachowicz, W. M.; Wiercigroch, M.

In: Smart Materials & Structures, Vol. 12, No. 3, 28.04.2003, p. 338-346.

Research output: Contribution to journalArticle

Zak, A. J. ; Cartmell, M. P. ; Ostachowicz, W. M. ; Wiercigroch, M. / One-dimensional shape memory alloy models for use with reinforced composite structures. In: Smart Materials & Structures. 2003 ; Vol. 12, No. 3. pp. 338-346.
@article{22b91b3ffc054f7ebf48e5fb2f5a2038,
title = "One-dimensional shape memory alloy models for use with reinforced composite structures",
abstract = "In this paper three models of the shape memory alloy behaviour have been presented and re-investigated. The models are attributed to Tanaka, Liang and Rogers, and Brinson, and have been used extensively in the literature for studying the static or dynamic performance of different composite material structures with embedded shape memory alloy components. The major differences and similarities between these models have been emphasised and examined in the paper. A simple experimental rig was designed and manufactured to gain additional insight into the main mechanics governing the shape memory alloy (SMA) mechanical properties. Data obtained from the experimental measurements on Ni-Ti wires have been used in the numerical simulation for validation purposes. It has been found that the three models all agree well in their predictions of the superelastic behaviour at higher temperatures, above the austenite finish temperature when shape memory alloys stay in the fully austenitic phase. However, at low temperatures, when the alloys stay in the fully martensitic phase, some difficulties may be encountered. The model developed by Brinson introduces two new state variables and therefore two different mechanisms for the instigation of stress-induced and temperature-induced martensite. This enables more accurate predictions of the superelastic behaviour. In general, it can be recommended that for investigations of the shape memory and superelastic behaviour of shape memory alloy components the Brinson model, or refinements based on the Brinson model, should be applied.",
keywords = "natural frequencies, thermomechanical behavior, constitutive model, damping behavior, flexible beam, elastic beam, SMA wires, plate, transformation, deformation",
author = "Zak, {A. J.} and Cartmell, {M. P.} and Ostachowicz, {W. M.} and M. Wiercigroch",
note = "The authors wish to acknowledge the support provided for this research by the UK’s Engineering and Physical Sciences Research Council via grants GR/N06267, GR/N06298 and GR/N06328. The support of Rolls-Royce plc is also gratefully acknowledged.",
year = "2003",
month = "4",
day = "28",
doi = "10.1088/0964-1726/12/3/304",
language = "English",
volume = "12",
pages = "338--346",
journal = "Smart Materials & Structures",
issn = "0964-1726",
publisher = "IOP Publishing Ltd.",
number = "3",

}

TY - JOUR

T1 - One-dimensional shape memory alloy models for use with reinforced composite structures

AU - Zak, A. J.

AU - Cartmell, M. P.

AU - Ostachowicz, W. M.

AU - Wiercigroch, M.

N1 - The authors wish to acknowledge the support provided for this research by the UK’s Engineering and Physical Sciences Research Council via grants GR/N06267, GR/N06298 and GR/N06328. The support of Rolls-Royce plc is also gratefully acknowledged.

PY - 2003/4/28

Y1 - 2003/4/28

N2 - In this paper three models of the shape memory alloy behaviour have been presented and re-investigated. The models are attributed to Tanaka, Liang and Rogers, and Brinson, and have been used extensively in the literature for studying the static or dynamic performance of different composite material structures with embedded shape memory alloy components. The major differences and similarities between these models have been emphasised and examined in the paper. A simple experimental rig was designed and manufactured to gain additional insight into the main mechanics governing the shape memory alloy (SMA) mechanical properties. Data obtained from the experimental measurements on Ni-Ti wires have been used in the numerical simulation for validation purposes. It has been found that the three models all agree well in their predictions of the superelastic behaviour at higher temperatures, above the austenite finish temperature when shape memory alloys stay in the fully austenitic phase. However, at low temperatures, when the alloys stay in the fully martensitic phase, some difficulties may be encountered. The model developed by Brinson introduces two new state variables and therefore two different mechanisms for the instigation of stress-induced and temperature-induced martensite. This enables more accurate predictions of the superelastic behaviour. In general, it can be recommended that for investigations of the shape memory and superelastic behaviour of shape memory alloy components the Brinson model, or refinements based on the Brinson model, should be applied.

AB - In this paper three models of the shape memory alloy behaviour have been presented and re-investigated. The models are attributed to Tanaka, Liang and Rogers, and Brinson, and have been used extensively in the literature for studying the static or dynamic performance of different composite material structures with embedded shape memory alloy components. The major differences and similarities between these models have been emphasised and examined in the paper. A simple experimental rig was designed and manufactured to gain additional insight into the main mechanics governing the shape memory alloy (SMA) mechanical properties. Data obtained from the experimental measurements on Ni-Ti wires have been used in the numerical simulation for validation purposes. It has been found that the three models all agree well in their predictions of the superelastic behaviour at higher temperatures, above the austenite finish temperature when shape memory alloys stay in the fully austenitic phase. However, at low temperatures, when the alloys stay in the fully martensitic phase, some difficulties may be encountered. The model developed by Brinson introduces two new state variables and therefore two different mechanisms for the instigation of stress-induced and temperature-induced martensite. This enables more accurate predictions of the superelastic behaviour. In general, it can be recommended that for investigations of the shape memory and superelastic behaviour of shape memory alloy components the Brinson model, or refinements based on the Brinson model, should be applied.

KW - natural frequencies

KW - thermomechanical behavior

KW - constitutive model

KW - damping behavior

KW - flexible beam

KW - elastic beam

KW - SMA wires

KW - plate

KW - transformation

KW - deformation

UR - http://www.scopus.com/inward/record.url?scp=0038545844&partnerID=8YFLogxK

U2 - 10.1088/0964-1726/12/3/304

DO - 10.1088/0964-1726/12/3/304

M3 - Article

VL - 12

SP - 338

EP - 346

JO - Smart Materials & Structures

JF - Smart Materials & Structures

SN - 0964-1726

IS - 3

ER -