Smooth particle hydrodynamics study of surface defect machining for diamond turning of silicon

Amir Mir, Xichun Luo, Amir Siddiq

Research output: Contribution to journalArticle

8 Citations (Scopus)
5 Downloads (Pure)

Abstract

This paper presents the feasibility study of potential application of recently developed surface defect machining (SDM) method in the fabrication of silicon and similar hard and brittle materials using smooth particle hydrodynamics (SPH) simulation approach. Simulation study of inverse parametric analysis was carried out to determine the Drucker-Prager (DP) constitutive model parameters of silicon by analysing the deformed material response behaviour using various DP model parameters. Indentation test simulations were carried out to perform inverse parametric study. SPH approach was exploited to machine silicon using conventional and surface defect machining method. To this end, we delve into opportunities of exploiting SDM through optimised machining quality, reduced machining time and lowering cost. The results of the conventional simulation were compared with the results of experimental diamond turning of silicon. In the SPH simulations, various types of surface defects were introduced on the workpiece prior to machining. Surface defects were equally distributed on the top face of the workpiece. The simulation study encompasses the investigation of chip formation, resultant machining forces, stresses and hydrostatic pressure with and without SDM. The study reveals the SDM process is an effective technique to manufacture hard and brittle materials as well as facilitate increased tool life. The study also divulges the importance of SPH evading the mesh distortion problem and offer natural chip formation during machining of hard and brittle materials.
Original languageEnglish
Pages (from-to)2461–2476
Number of pages16
JournalThe International Journal of Advanced Manufacturing Technology
Volume88
Issue number9
Early online date2 Jun 2016
DOIs
Publication statusPublished - 1 Feb 2017

Fingerprint

Surface defects
Diamonds
Machining
Hydrodynamics
Silicon
Brittleness
Hydrostatic pressure
Constitutive models
Indentation
Fabrication

Keywords

  • surface defect machining
  • diamond turning
  • silicon
  • SPH

Cite this

Smooth particle hydrodynamics study of surface defect machining for diamond turning of silicon. / Mir, Amir; Luo, Xichun ; Siddiq, Amir.

In: The International Journal of Advanced Manufacturing Technology , Vol. 88, No. 9, 01.02.2017, p. 2461–2476.

Research output: Contribution to journalArticle

@article{990dbabfd87041c4b1230f660b52ecb5,
title = "Smooth particle hydrodynamics study of surface defect machining for diamond turning of silicon",
abstract = "This paper presents the feasibility study of potential application of recently developed surface defect machining (SDM) method in the fabrication of silicon and similar hard and brittle materials using smooth particle hydrodynamics (SPH) simulation approach. Simulation study of inverse parametric analysis was carried out to determine the Drucker-Prager (DP) constitutive model parameters of silicon by analysing the deformed material response behaviour using various DP model parameters. Indentation test simulations were carried out to perform inverse parametric study. SPH approach was exploited to machine silicon using conventional and surface defect machining method. To this end, we delve into opportunities of exploiting SDM through optimised machining quality, reduced machining time and lowering cost. The results of the conventional simulation were compared with the results of experimental diamond turning of silicon. In the SPH simulations, various types of surface defects were introduced on the workpiece prior to machining. Surface defects were equally distributed on the top face of the workpiece. The simulation study encompasses the investigation of chip formation, resultant machining forces, stresses and hydrostatic pressure with and without SDM. The study reveals the SDM process is an effective technique to manufacture hard and brittle materials as well as facilitate increased tool life. The study also divulges the importance of SPH evading the mesh distortion problem and offer natural chip formation during machining of hard and brittle materials.",
keywords = "surface defect machining , diamond turning, silicon, SPH",
author = "Amir Mir and Xichun Luo and Amir Siddiq",
note = "Acknowledgments The authors would like to thank EPSRC (EP/K018345/1) and Royal Society-NSFC International Exchange Scheme for providing financial support to this research.",
year = "2017",
month = "2",
day = "1",
doi = "10.1007/s00170-016-8940-6",
language = "English",
volume = "88",
pages = "2461–2476",
journal = "The International Journal of Advanced Manufacturing Technology",
issn = "0268-3768",
publisher = "Springer London",
number = "9",

}

TY - JOUR

T1 - Smooth particle hydrodynamics study of surface defect machining for diamond turning of silicon

AU - Mir, Amir

AU - Luo, Xichun

AU - Siddiq, Amir

N1 - Acknowledgments The authors would like to thank EPSRC (EP/K018345/1) and Royal Society-NSFC International Exchange Scheme for providing financial support to this research.

PY - 2017/2/1

Y1 - 2017/2/1

N2 - This paper presents the feasibility study of potential application of recently developed surface defect machining (SDM) method in the fabrication of silicon and similar hard and brittle materials using smooth particle hydrodynamics (SPH) simulation approach. Simulation study of inverse parametric analysis was carried out to determine the Drucker-Prager (DP) constitutive model parameters of silicon by analysing the deformed material response behaviour using various DP model parameters. Indentation test simulations were carried out to perform inverse parametric study. SPH approach was exploited to machine silicon using conventional and surface defect machining method. To this end, we delve into opportunities of exploiting SDM through optimised machining quality, reduced machining time and lowering cost. The results of the conventional simulation were compared with the results of experimental diamond turning of silicon. In the SPH simulations, various types of surface defects were introduced on the workpiece prior to machining. Surface defects were equally distributed on the top face of the workpiece. The simulation study encompasses the investigation of chip formation, resultant machining forces, stresses and hydrostatic pressure with and without SDM. The study reveals the SDM process is an effective technique to manufacture hard and brittle materials as well as facilitate increased tool life. The study also divulges the importance of SPH evading the mesh distortion problem and offer natural chip formation during machining of hard and brittle materials.

AB - This paper presents the feasibility study of potential application of recently developed surface defect machining (SDM) method in the fabrication of silicon and similar hard and brittle materials using smooth particle hydrodynamics (SPH) simulation approach. Simulation study of inverse parametric analysis was carried out to determine the Drucker-Prager (DP) constitutive model parameters of silicon by analysing the deformed material response behaviour using various DP model parameters. Indentation test simulations were carried out to perform inverse parametric study. SPH approach was exploited to machine silicon using conventional and surface defect machining method. To this end, we delve into opportunities of exploiting SDM through optimised machining quality, reduced machining time and lowering cost. The results of the conventional simulation were compared with the results of experimental diamond turning of silicon. In the SPH simulations, various types of surface defects were introduced on the workpiece prior to machining. Surface defects were equally distributed on the top face of the workpiece. The simulation study encompasses the investigation of chip formation, resultant machining forces, stresses and hydrostatic pressure with and without SDM. The study reveals the SDM process is an effective technique to manufacture hard and brittle materials as well as facilitate increased tool life. The study also divulges the importance of SPH evading the mesh distortion problem and offer natural chip formation during machining of hard and brittle materials.

KW - surface defect machining

KW - diamond turning

KW - silicon

KW - SPH

U2 - 10.1007/s00170-016-8940-6

DO - 10.1007/s00170-016-8940-6

M3 - Article

VL - 88

SP - 2461

EP - 2476

JO - The International Journal of Advanced Manufacturing Technology

JF - The International Journal of Advanced Manufacturing Technology

SN - 0268-3768

IS - 9

ER -